Toyota 4afe Ecu Pinout Online

A: Japanese domestic market (JDM) and European (EDM) ECUs used slightly different wire colors. For example, JDM 4A-FEs often use a Yellow/White wire for injector #1 instead of Red/White. Always use a multimeter to confirm continuity from the sensor to the ECU pin number—ignore the color.

However, when things go wrong—or when you plan a standalone ECU swap or engine conversion—the wiring becomes the biggest headache. The Engine Control Unit (ECU) is the brain, but without a proper , that brain is just a plastic box with two connectors. toyota 4afe ecu pinout

| Pin | Wire Color | Signal Name | Function | | :--- | :--- | :--- | :--- | | | Purple | TACH | Tachometer Output (from igniter via ECU) | | C02 | Yellow | NSW | Neutral Start Switch (Auto only) / Clutch switch (Manual) | | C03 | Red/Black | L | Oil Pressure Warning Light (some markets) | | C04 | Black | E2 | Ground for sensors (duplicate of B13) | | C05 | Pink | M-REL | Main EFI Relay Control (ECU turns relay ON) | | C06 | Green/Red | VTA2 | TPS Closed Throttle Position Switch (IDL) | | C07 | Green | VCC2 | Secondary 5V reference (rarely used) | | C08 | - | - | Empty | | C09 | Yellow/Blue | TC | Diagnostic Communication Line (OBD-I scanner) | | C10 | Black/Red | A/C IDL | A/C Idle-Up Signal (raises idle when A/C is on) | | C11 | Red | BATT | Constant 12V for ECU keep-alive memory | | C12 | Yellow/Green | STP | Stop Light Switch Signal (brake pedal input) | Part 3: Key Differences – AFM vs. MAP (Type 1 vs. Type 2) If you own a pre-1992 4A-FE, your ECU pinout will differ significantly. Do not use the pinout above for a 1989 Corolla. A: Japanese domestic market (JDM) and European (EDM)

| Pin | Wire Color | Signal Name | Function | | :--- | :--- | :--- | :--- | | | White | IGT | Ignition Timing Signal (from ECU to igniter) | | B02 | Red/White | #10 | Fuel Injector Cylinder #1 | | B03 | Blue | #20 | Fuel Injector Cylinder #2 | | B04 | Yellow | #30 | Fuel Injector Cylinder #3 | | B05 | Brown | #40 | Fuel Injector Cylinder #4 | | B06 | Black/Yellow | FC | Circuit Opening Relay (Fuel Pump Control) | | B07 | Light Green | VSV (CC) | Charcoal Canister Purge VSV | | B08 | - | - | Empty | | B09 | Red/White | +BM | Backup power for ECU memory (constant 12V) | | B10 | Black/Orange | W | Check Engine Light (MIL) Control | | B11 | Blue/White | ACT | Air Conditioning Switch Signal (to ECU) | | B12 | Red/Black | ACMG | A/C Compressor Magnetic Clutch Relay | | B13 | Black | E1 | Sensor Ground (shared with TPS, MAP, etc.) | | B14 | Black/White | E03 | Injector Power Ground | | B15 | Black/White | E04 | Injector Power Ground | | B16 | - | TE1 | Diagnostic Jumper Pin (for flashing CEL codes) | However, when things go wrong—or when you plan

Pins B02-B05 (injectors) are switched grounds. The ECU grounds these wires to fire the injectors. You will not see 12V here with the key on. Instead, each wire should show continuity to ground for a brief pulse when cranking. Connector C (12 pins) – Auxiliary & Diagnostics This connector handles extra sensors, tachometer, and diagnostics.

A: The 7AFE (1.8L version) ECU has different fuel maps and ignition timing. It will run a 4AFE, but poorly—rich at idle and lean at high RPM. Pinouts are similar but not identical. Not recommended.

Drop a comment below (if applicable) or consult the factory Toyota Electrical Wiring Diagram (EWD) for your specific chassis code.